Progress on the Whippet

I made a mount for the battery out of angle iron, I don't have a good picture but, it just follows the perimeter of the battery then has a clamp that goes over the top.

 It's been slow going on the Whippet lately but, I have been able to get a few things done.  The above picture shows the rear panel that I made to tie the rear together.  I made it from 18 gauge.  Its hard to do long bends without a brake but, if you take your time you can do it with some clamps, angle iron and hammer/dolly work.

This is just a shot of the inside of the panel.

I cut down the decklid to make it fit better and installed the taillights. 

I installed a piano hinge on the bottom of the decklid and got some spring latches for the top that I haven't mounted yet.  I am currently working on bleeding the brakes after installing all new brake components from Thompson's Garage and a new 48' ford style master cylinder from Speedway Motors. 

Till next time keep your ears and eyes open for hidden car treasure!

1929 Willy'sWhippet Model A Frame Construction Body

My original plan was to use this saginaw 3 speed transmission from a 57' Chevy with an Offy adapter that you can see in the picture. I would have then had to convert the rearend to an open driveline because it uses a torque tube from the factory. 

But I found a 1946 Ford 3 speed transmission for less than the cost of the open drive conversion kit and it makes it a bit more traditional in style.

The next group of pictures is the process of adding steel structure to the body and basically creating framing for the floor sheet metal to attach to.



I left the center open to allow travel of the torque tube under suspension compression.



I then framed a higher section to cover the open torque tube area.

There is one more stick to put in here but you get the idea.

Of course having the engine mocked up in place is essential to getting the rest of the car's proportion right.



Val and Glasgow Mt, 1933 Ford 33' Plymouth

So yesterday I made the 3-1/2 hour trip to Glasgow Montana to get a 1934 Ford Frame for my new 33' Ford Pickup project.  My friend Jerry also lives there so it was a trip well worth the drive.  After I picked up the frame Jerry and I went on a hot rod  tour of Glasgow. 

We started at Jerry's where he showed me a picture of a car I was told about by my father when I was in high school.  I have been looking for this car ever since my dad told me about.  Needless to say I still haven't found it.  I was amazed to see that Jerry had a picture.

Larry Deal owned the car, that is Murk Mansel in the passenger seat.  This picture was taken in April of 1963.

Jerry has got a 70' Mustang Mach 1 that he bought new, it has 16,000 original miles on it.  The car looks brand new, it still has the original tires on it!  I'm kicking myself for not getting a picture of it, it's unbelievable.

Here is a couple pics of Jerry's 33' Ford coupe I just might sell parts of my body to obtain, he fits 5 vehicles in his garage so it was a little cramped.

We cruised around town saw a couple rat rod projects and the front engine dragster seen below.

It doesn't have the engine in it right now but, it ran a 292 straight six...crazy.

This is at the Malta 1/8th mile track.

Here is another 33' Plymouth that a guy in glasgow is building.

I also met this guy Stormer, he sells rc cars on the internet and drag races.  He has some cool stuff on youtube, but here is his drag car.  It's a 4 cylinder...crazy.



1931 Chevrolet 5 Window Coupe Body

I set the body up on the firewall, it is the easiest way to square it up.

Here I started adding steel structure to the inside of the body.  Old Chevy's had wood for the body framing.  They basically made a wood frame then wrapped it in metal.

Here is the body before I chopped the roof about 4 inches.

After the chop.

You can see here the fiberglass trunk lid I bought from Speedway Motors, then I made the panel above and below the lid.

1929 Willy's Whippet, Ford Model A, Mercury Flathead,Frame Fabrication, Body Channelling, Pinion Angle, Firewall Reversal

Setting up the front suspension.  I am going to make what is called a "suicide perch" for the front axle.  If it were to fail the frame hits the ground, hence suicide.

Just a shot of how I connected the rear suspension and the rear frame section that I made.  The wheelbase is longer than a Model A and on a Model A the rear spring is directly above the rear axle.

I cut the frame horns off the Model A Frame and removed the front stock cross member, both items that easily get you a couple hundred bucks on ebay.  Money toward the project!

Here I set the pinion angle at +3 degrees for suspension compression under acceleration.

Here I have the body channelled 6 inches over the frame.

You can see the first part of the front spring perch welded on.  I later add bracing to it.

A closer view of the semi-finished suicide spring perch.  I made it tall to get the car low to the ground.

I removed the firewall to reverse it and give me the engine bay clearance I need.  Reversing is just flipping it around.

Here the firewall is reversed and welded in.  The hole in the side of the cowl is for the cowl steering which I will show later.  I cut the tops of the doors off, welded the doors shut, removed the windshield sun visor, and chopped the windshield frame about 3-1/2 inches.

I have the driver side door top folded over, you can see the original height on the passenger door waiting to be done.

1929 Willy's Whippet, Ford Model A, Hot Rod, Mercury Flathead

Started with a pretty bare Ford Model A Frame

I started this project about 3 years ago with the intention of taking parts I already had, putting them to together and making a rolling project that I could sell and make some coin off.

I made the rear section out of new 2x4 box tubing.  I stepped it up to get the car lower and extended it rearward to use a spring behind banjo rear differential.

I also needed something to occupy my mind that winter, so I rounded everything up and brought it to my garage in October 2009.

1949 Mercury 8CM Flathead

I had an old Ford farm truck that had this Mercury Flathead V8 in it and it still spun over so I yanked it out and started tearing it down.

1936-39 Ford Wide Five Wheels and Brake Drums

I used part of the Model A frame that I cut off to make a rear cross brace and then used c channel from another frame section to make this rear spring perch.

Here is the 1929 Whippet body as I bought it.  I sold it on ebay and I think the guy who bought it died and nobody came to pick it up.  It is a Sport Coupe, it used to have a leather top like a convertible.

1927 Chevrolet Frame Fabrication, Engine, Transmission Placement, 1931 Chevy Coupe Build, Pinion Angle

We cut a few inches off the rear and moved the crossmember forward

So my friend Josh came to Oregon to help me for a week.  He is a welder and would make sure the frame was done correctly.

The rearend was from a Caddilac limo and had this triangulated four link design already built in so it worked great.

Making the sparks fly!

We set the engine in place and the cowl to make sure everything was going to fit.

Here the Ford Model A front crossmember is installed to lower the front end.  You can see that the frame is fully boxed now too.  Always make your body mounts before boxing the frame, I failed to do that on this car.

The motor mounts and the transmission crossmember are installed.  I bought Model A to Chevy 350 motor mounts and modified them to fit the wider frame of a 27' Chevy.  I got a 40' Ford axle off ebay, some 39' Ford spindles off ebay then the rest of the frontend parts from Speedway Motors.

We made some upper shock mounts for the rear.

This is basically the progress Josh and I made for the week.  The transmission angle is -3 degrees and the rear differential pinion angle is +3 degrees so when the suspension compresses under acceleration the drive shaft is at 0 degrees.